ICALEPCS2023 - List of Authors (Saveri Silva, M.)

Paper	Title	Page
MO2AO07	Dynamical Modelling Validation and Control Development for the New High-Dynamic Double-Crystal Monochromator (HD-DCM-Lite) for Sirius/LNLS	100
	T.R. Silva Soares, J.P.S. Furtado, R.R. Geraldes, M. Saveri Silva, G.S. de Albuquerque LNLS, Campinas, Brazil
	Two new High-Dynamic Double-Crystal Monochromators (HD-DCM-Lite) are under installation in Sirius/LNLS for the new beamlines QUATI (quick-EXAFS) and SAPUCAIA (SAXS), which requires high in-position stability (5 nrad RMS in terms of pitch) whereas QUATI’s DCM demands the ability to perform quick sinusoidal scans in frequencies, for example 15 Hz at 4 mrad peak-to-peak amplitude. Therefore, this equipment aims to figure as an unparalleled bridge between slow step-scan DCMs, and channel-cut quick-EXAFS monochromators. In the previous conference, the dynamical modelling of HD-DCM-Lite was presented, indicating the expected performance to achieve QUATI and SAPUCAIA requirements. In this work, we are going to present the offline validation of the dynamical modelling, comparing to the solutions achieved for the previous version of LNLS HD-DCMs. This work also presents the hardware-based control architecture development, discussing the loop shaping technique and upgrades in the system, such as the increase of the position resolution, synchronization of the rotary stages, and FPGA code optimization. Furthermore, we describe how the motion controller was developed, given the high-performance motion control, such as complex control algorithm in parallel with a minimal jitter and the expectations for the beamlines commissioning regarding detector and undulator synchronization.
	Slides MO2AO07 [2.432 MB]
DOI •	reference for this paper ※ doi:10.18429/JACoW-ICALEPCS2023-MO2AO07
About •	Received ※ 06 October 2023 — Revised ※ 07 October 2023 — Accepted ※ 12 December 2023 — Issued ※ 19 December 2023
Cite •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

Paper

Title

Page

Dynamical Modelling Validation and Control Development for the New High-Dynamic Double-Crystal Monochromator (HD-DCM-Lite) for Sirius/LNLS

100

T.R. Silva Soares, J.P.S. Furtado, R.R. Geraldes, M. Saveri Silva, G.S. de Albuquerque
LNLS, Campinas, Brazil

Two new High-Dynamic Double-Crystal Monochromators (HD-DCM-Lite) are under installation in Sirius/LNLS for the new beamlines QUATI (quick-EXAFS) and SAPUCAIA (SAXS), which requires high in-position stability (5 nrad RMS in terms of pitch) whereas QUATI’s DCM demands the ability to perform quick sinusoidal scans in frequencies, for example 15 Hz at 4 mrad peak-to-peak amplitude. Therefore, this equipment aims to figure as an unparalleled bridge between slow step-scan DCMs, and channel-cut quick-EXAFS monochromators. In the previous conference, the dynamical modelling of HD-DCM-Lite was presented, indicating the expected performance to achieve QUATI and SAPUCAIA requirements. In this work, we are going to present the offline validation of the dynamical modelling, comparing to the solutions achieved for the previous version of LNLS HD-DCMs. This work also presents the hardware-based control architecture development, discussing the loop shaping technique and upgrades in the system, such as the increase of the position resolution, synchronization of the rotary stages, and FPGA code optimization. Furthermore, we describe how the motion controller was developed, given the high-performance motion control, such as complex control algorithm in parallel with a minimal jitter and the expectations for the beamlines commissioning regarding detector and undulator synchronization.

Slides MO2AO07 [2.432 MB]

DOI •

reference for this paper ※ doi:10.18429/JACoW-ICALEPCS2023-MO2AO07

About •

Received ※ 06 October 2023 — Revised ※ 07 October 2023 — Accepted ※ 12 December 2023 — Issued ※ 19 December 2023

Cite •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)