ICALEPCS2023 - List of Authors (Sapozhnikov, L.)

Paper	Title	Page
TUPDP125	Design and Implementation the LCLS-II Machine Protection System	877
	J.A. Mock, Z.A. Domke, R.T. Herbst, P. Krejcik, R. Ruckman, L. Sapozhnikov SLAC, Menlo Park, California, USA
	The linear accelerator complex at the SLAC National Accelerator Laboratory has been upgraded to include LCLS-II, a new linac capable of producing beam power as high as several hundred kW with CW beam rates up to 1 MHz while maintaining existing capabilities from the copper machine. Because of these high-power beams, a new Machine Protection System with a latency of less than 100 us was designed and installed to prevent damage to the machine when a fault or beam loss is detected. The new LCLS-II MPS must work in parallel with the existing MPS from the respective sources all the way through the user hutches to provide a mechanism to reduce the beam rate or shut down operation in a beamline without impacting the neighboring beamline when a fault condition is detected. Because either beamline can use either accelerator as its source and each accelerator has different operating requirements, great care was taken in the overall system design to ensure the necessary operation can be achieved with a seamless experience for the accelerator operators. The overall system design of the LCLS-II MPS software including the ability to interact with the existing systems and the tools developed for the control room to provide the user operation experience will be described.
	Poster TUPDP125 [1.360 MB]
DOI •	reference for this paper ※ doi:10.18429/JACoW-ICALEPCS2023-TUPDP125
About •	Received ※ 04 October 2023 — Revised ※ 30 November 2023 — Accepted ※ 04 December 2023 — Issued ※ 14 December 2023
Cite •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THPDP087	LCLS-II Controls Software Architecture for the Wire Scan Diagnostics	1556
	N. Balakrishnan, J.D. Bong, A.S. Fisher, B.T. Jacobson, L. Sapozhnikov SLAC, Menlo Park, California, USA
	Funding: This work was supported by Department of Energy, Office of Basic Energy Sciences, contract DE-AC02-76SF00515 The Super Conducting (SC) Linac Coherent Light Source II (LCLS-II) facility at SLAC is capable of delivering an electron beam at a fast rate of up to 1MHz. The high-rate necessitates the processing algorithms and data exchanges with other high-rate systems to be implemented with FPGA technology. For LCLS-II, SLAC has deployed a common platform solution (hardware, firmware, software) which is used by timing, machine protection and diagnostics systems. The wire scanner diagnostic system uses this solution to acquire beam synchronous time-stamped readings, of wire scanner position and beam loss during the scan, for each individual bunch. This paper explores the software architecture and control system integration for LCLS-II wire scanners using the common platform solution.
	Poster THPDP087 [1.079 MB]
DOI •	reference for this paper ※ doi:10.18429/JACoW-ICALEPCS2023-THPDP087
About •	Received ※ 06 October 2023 — Revised ※ 10 October 2023 — Accepted ※ 06 December 2023 — Issued ※ 09 December 2023
Cite •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

Paper

Title

Page

Design and Implementation the LCLS-II Machine Protection System

877

J.A. Mock, Z.A. Domke, R.T. Herbst, P. Krejcik, R. Ruckman, L. Sapozhnikov
SLAC, Menlo Park, California, USA

The linear accelerator complex at the SLAC National Accelerator Laboratory has been upgraded to include LCLS-II, a new linac capable of producing beam power as high as several hundred kW with CW beam rates up to 1 MHz while maintaining existing capabilities from the copper machine. Because of these high-power beams, a new Machine Protection System with a latency of less than 100 us was designed and installed to prevent damage to the machine when a fault or beam loss is detected. The new LCLS-II MPS must work in parallel with the existing MPS from the respective sources all the way through the user hutches to provide a mechanism to reduce the beam rate or shut down operation in a beamline without impacting the neighboring beamline when a fault condition is detected. Because either beamline can use either accelerator as its source and each accelerator has different operating requirements, great care was taken in the overall system design to ensure the necessary operation can be achieved with a seamless experience for the accelerator operators. The overall system design of the LCLS-II MPS software including the ability to interact with the existing systems and the tools developed for the control room to provide the user operation experience will be described.

Poster TUPDP125 [1.360 MB]

DOI •

reference for this paper ※ doi:10.18429/JACoW-ICALEPCS2023-TUPDP125

About •

Received ※ 04 October 2023 — Revised ※ 30 November 2023 — Accepted ※ 04 December 2023 — Issued ※ 14 December 2023

Cite •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THPDP087

LCLS-II Controls Software Architecture for the Wire Scan Diagnostics

1556

N. Balakrishnan, J.D. Bong, A.S. Fisher, B.T. Jacobson, L. Sapozhnikov
SLAC, Menlo Park, California, USA

Funding: This work was supported by Department of Energy, Office of Basic Energy Sciences, contract DE-AC02-76SF00515
The Super Conducting (SC) Linac Coherent Light Source II (LCLS-II) facility at SLAC is capable of delivering an electron beam at a fast rate of up to 1MHz. The high-rate necessitates the processing algorithms and data exchanges with other high-rate systems to be implemented with FPGA technology. For LCLS-II, SLAC has deployed a common platform solution (hardware, firmware, software) which is used by timing, machine protection and diagnostics systems. The wire scanner diagnostic system uses this solution to acquire beam synchronous time-stamped readings, of wire scanner position and beam loss during the scan, for each individual bunch. This paper explores the software architecture and control system integration for LCLS-II wire scanners using the common platform solution.

Poster THPDP087 [1.079 MB]

DOI •

reference for this paper ※ doi:10.18429/JACoW-ICALEPCS2023-THPDP087

About •

Received ※ 06 October 2023 — Revised ※ 10 October 2023 — Accepted ※ 06 December 2023 — Issued ※ 09 December 2023

Cite •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)