ICALEPCS2023 - List of Authors (Biallas, G.H.)

Paper	Title	Page
WE3AO05	Helium Mass Flow System Integrated into EPICS for Online SRF Cavity Q Measurements	1071
	K. Jordan, G.R. Croke, J.P. Jayne, M.G. Tiefenback, C.M. Wilson JLab, Newport News, Virginia, USA G.H. Biallas Hyperboloid LLC, Yorktown, Virginia, USA D.P. Christian JLAB, Newport News, USA
	The SBIR funded Helium Mass Flow Monitor System, developed by Jefferson Lab and Hyperboloid LLC, is designed to measure the health of cavities in a Cryomodule in real-time. It addresses the problem of cavities with low Q₀, which generate excess heat and evaporation from the 2 K super-fluid helium bath used to cool the cavities. The system utilizes a unique meter that is based on a superconducting component. This device enables high-resolution measurements of the power dissipated in the cryomodule while the accelerator is operating. It can also measure individual Cavity Q₀s when the beam is turned off. The Linux-based control system is an integral part of this device, providing the necessary control and data processing capabilities. The initial implementation of the Helium Mass Flow Monitor System at Jefferson Lab was done using LabView, a couple of current sources & a nano-voltmeter. Once the device was proven to work at 2K the controls transitioned to a hand wired PCB & Raspberry Pi interfaced to the open-source Experimental Physics and Industrial Control System (EPICS) control system. The EE support group preferred to support a LabJack T7 over the rPi. 12 chassis were built and the system is being deployed as the cryogenic U-Tubes become available.
	Slides WE3AO05 [6.073 MB]
DOI •	reference for this paper ※ doi:10.18429/JACoW-ICALEPCS2023-WE3AO05
About •	Received ※ 09 October 2023 — Revised ※ 12 October 2023 — Accepted ※ 14 December 2023 — Issued ※ 18 December 2023
Cite •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

Paper

Title

Page

Helium Mass Flow System Integrated into EPICS for Online SRF Cavity Q Measurements

1071

K. Jordan, G.R. Croke, J.P. Jayne, M.G. Tiefenback, C.M. Wilson
JLab, Newport News, Virginia, USA
G.H. Biallas
Hyperboloid LLC, Yorktown, Virginia, USA
D.P. Christian
JLAB, Newport News, USA

The SBIR funded Helium Mass Flow Monitor System, developed by Jefferson Lab and Hyperboloid LLC, is designed to measure the health of cavities in a Cryomodule in real-time. It addresses the problem of cavities with low Q₀, which generate excess heat and evaporation from the 2 K super-fluid helium bath used to cool the cavities. The system utilizes a unique meter that is based on a superconducting component. This device enables high-resolution measurements of the power dissipated in the cryomodule while the accelerator is operating. It can also measure individual Cavity Q₀s when the beam is turned off. The Linux-based control system is an integral part of this device, providing the necessary control and data processing capabilities. The initial implementation of the Helium Mass Flow Monitor System at Jefferson Lab was done using LabView, a couple of current sources & a nano-voltmeter. Once the device was proven to work at 2K the controls transitioned to a hand wired PCB & Raspberry Pi interfaced to the open-source Experimental Physics and Industrial Control System (EPICS) control system. The EE support group preferred to support a LabJack T7 over the rPi. 12 chassis were built and the system is being deployed as the cryogenic U-Tubes become available.

Slides WE3AO05 [6.073 MB]

DOI •

reference for this paper ※ doi:10.18429/JACoW-ICALEPCS2023-WE3AO05

About •

Received ※ 09 October 2023 — Revised ※ 12 October 2023 — Accepted ※ 14 December 2023 — Issued ※ 18 December 2023

Cite •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)