ICALEPCS2023 - List of Authors (Andreassen, O.O.)

Paper	Title	Page
TUPDP087	Enhancing Measurement Quality in HL-LHC Magnets Testing Using Software Techniques on Digital Multimeter Cards-Based System	729
	H. Reymond, O.Ø. Andreassen, M. Charrondiere, C. Charrondière, P.D. Jankowski CERN, Meyrin, Switzerland
	The HL-LHC magnets play a critical role in the High-Luminosity Large Hadron Collider project, which aims to increase the luminosity of the LHC and enable more precise studies of fundamental physics. Ensuring the performance and reliability of these magnets requires high-precision measurements of their electrical properties during testing. To meet the R&D program needs of the new superconducting magnet technology, an accurate and generic voltage measurement system was developed after the testing and validation campaign of the LHC magnets. The system was based on a set of digital multimeter (DMM) cards installed in a PXI modular chassis and controlled using CERN’s in-house software development. It allowed for the measurement of the electrical properties of the magnet prototypes during their study phase. However, during the renovation of the magnet test benches and in preparation for the HL-LHC magnet series measurement, some limitations and instabilities were discovered during long recording measurements. As a result, it was decided to redesign the measurement system. The emergence and promises of the new PXIe platform, along with the requirement to build eight new systems to be operated similarly to the existing four, led to a complete redesign of the software. This article describes the various software techniques employed to address platform compatibility issues and significantly improve measurement accuracy, thus ensuring the reliability and quality of the data obtained from the HL-LHC magnet tests.
	Poster TUPDP087 [6.660 MB]
DOI •	reference for this paper ※ doi:10.18429/JACoW-ICALEPCS2023-TUPDP087
About •	Received ※ 02 October 2023 — Revised ※ 09 October 2023 — Accepted ※ 12 October 2023 — Issued ※ 13 October 2023
Cite •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUPDP088	Labview-Based Template for Enhanced Accelerator Systems Control: Software Solutions for the CERN-ISOLDE Facilities	735
	C. Charrondière, O.Ø. Andreassen, A. Benoit, E.G. Galetti, R. Heinke, L.L. Le, B.A. Marsh, R.E. Rossel, S. Rothe, S. Sudak CERN, Meyrin, Switzerland G.E. Boorman Royal Holloway, University of London, Surrey, United Kingdom
	ISOLDE is part of the experimental infrastructure with-in the CERN accelerator complex that provides radioac-tive ion beams for studies of fundamental nuclear phys-ics, astrophysics, condensed matter physics and medical applications. Complementing the available controls in-frastructure, an easy-to-use set of applications was devel-oped to allow operators to record and display signals from multiple sources, as well as to provide drivers for non-standard, custom-made instruments and specialized off-the-shelf components. Aimed not only at software engineers but developers with any background, a generic and modular software template was developed in LabVIEW following a collab-oration between CERN and ANGARA Technology. This unified template can be extended to support interaction with any instrument and any newly developed applica-tion can be easily added to the existing control system and integrated into the CERN control and monitoring infrastructure. New modules and instrument drivers are easy to maintain as the structure and communication layers are all derived from the same template and based on the same components. In this paper, we will explain the implementation, ar-chitecture and structure of the template, as well as a wide variety of use cases - from motor control to image acquisi-tion and laser-specific equipment control. We will also show use cases of applications developed and deployed within a few days in the ISOLDE facility.
	Poster TUPDP088 [0.860 MB]
DOI •	reference for this paper ※ doi:10.18429/JACoW-ICALEPCS2023-TUPDP088
About •	Received ※ 20 September 2023 — Revised ※ 09 October 2023 — Accepted ※ 12 October 2023 — Issued ※ 23 October 2023
Cite •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TH2BCO04	SAMbuCa: Sensors Acquisition and Motion Control Framework at CERN	1179
	A. Masi, O.Ø. Andreassen, M. Arruat, M. Di Castro, R. Ferraro, I. Kozsar, E.W. Matheson, J.P. Palluel, P. Peronnard, J. Serrano, J. Tagg, F. Vaga, E. Van der Bij CERN, Meyrin, Switzerland S. Danzeca, M. Donzé, S.F. Fargier, M. Gulin, E. Soria European Organization for Nuclear Research (CERN), Geneva, Switzerland
	Motion control systems at CERN often have challenging requirements, such as high precision in extremely radioactive environments with millisecond synchronization. These demanding specifications are particularly relevant for Beam Intercepting Devices (BIDs) such as the collimators of the Large Hadron Collider (LHC). Control electronics must be installed in safe areas, hundreds of meters away from the sensors and actuators while conventional industrial systems only work with cable lengths up to a few tens of meters. To address this, several years of R&D have been committed to developing a high precision motion control system. This has resulted in specialized radiation-hard actuators, new sensors, novel algorithms and actuator control solutions capable of operating in this challenging environment. The current LHC Collimator installation is based on off-the-shelf components from National Instruments. During the Long Shutdown 3 (LS3 2026-2028), the existing systems will be replaced by a new high-performance Sensors Acquisition and Motion Control system (SAMbuCa). SAMbuCa represents a complete, in-house developed, flexible and modular solution, able to cope with the demanding requirements of motion control at CERN, and incorporating the R&D achievements and operational experience of the last 15 years controlling more than 1200 axes at CERN. In this paper, the hardware and software architectures, their building blocks and design are described in detail.
	Slides TH2BCO04 [5.775 MB]
DOI •	reference for this paper ※ doi:10.18429/JACoW-ICALEPCS2023-TH2BCO04
About •	Received ※ 05 October 2023 — Revised ※ 12 October 2023 — Accepted ※ 19 December 2023 — Issued ※ 20 December 2023
Cite •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THPDP002	The Micro-Services of Cern’s Critical Current Test Benches	1295
	C. Charrondière, A. Ballarino, C. Barth, J.F. Fleiter, P. Koziol, H. Reymond CERN, Meyrin, Switzerland O.Ø. Andreassen, T. Boutboul, S.C. Hopkins European Organization for Nuclear Research (CERN), Geneva, Switzerland
	In order to characterize the critical-current density of low temperature superconductors such as niobium¿titanium (NbTi) and niobium¿tin (Nb₃Sn) or high temperature superconductors such as magnesium-diboride MgB₂ or Rare-earth Barium Copper Oxide REBCO tapes, a wide range of custom instruments and interfaces are used. The critical current of a superconductor depends on temperature, magnetic field, current and strain, requiring high precision measurements in the nano Volt range, well-synchronized instrumentation, and the possibility to quickly adapt and replace instrumentation if needed. The micro-service based application presented in this paper allows operators to measure a variety of analog signals, such as the temperature of the cryostats and sample under test, magnetic field, current passing through the sample, voltage across the sample, pressure, helium level etc. During the run, the software protects the sample from quenching, controlling the current passed through it using high-speed field programmable gate array (FPGA) systems on Linux Real-Time (RT) based PCI eXtensions controllers (PXIe). The application records, analyzes and reports to the external Oracle database all parameters related to the test. In this paper, we describe the development of the micro-service based control system, how the interlocks and protection functionalities work, and how we had to develop a multi-windowed scalable acquisition application that could be adapted to the many changes occurring in the test facility.
	Poster THPDP002 [6.988 MB]
DOI •	reference for this paper ※ doi:10.18429/JACoW-ICALEPCS2023-THPDP002
About •	Received ※ 06 October 2023 — Revised ※ 10 October 2023 — Accepted ※ 13 October 2023 — Issued ※ 26 October 2023
Cite •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

Paper

Title

Page

Enhancing Measurement Quality in HL-LHC Magnets Testing Using Software Techniques on Digital Multimeter Cards-Based System

729

H. Reymond, O.Ø. Andreassen, M. Charrondiere, C. Charrondière, P.D. Jankowski
CERN, Meyrin, Switzerland

The HL-LHC magnets play a critical role in the High-Luminosity Large Hadron Collider project, which aims to increase the luminosity of the LHC and enable more precise studies of fundamental physics. Ensuring the performance and reliability of these magnets requires high-precision measurements of their electrical properties during testing. To meet the R&D program needs of the new superconducting magnet technology, an accurate and generic voltage measurement system was developed after the testing and validation campaign of the LHC magnets. The system was based on a set of digital multimeter (DMM) cards installed in a PXI modular chassis and controlled using CERN’s in-house software development. It allowed for the measurement of the electrical properties of the magnet prototypes during their study phase. However, during the renovation of the magnet test benches and in preparation for the HL-LHC magnet series measurement, some limitations and instabilities were discovered during long recording measurements. As a result, it was decided to redesign the measurement system. The emergence and promises of the new PXIe platform, along with the requirement to build eight new systems to be operated similarly to the existing four, led to a complete redesign of the software. This article describes the various software techniques employed to address platform compatibility issues and significantly improve measurement accuracy, thus ensuring the reliability and quality of the data obtained from the HL-LHC magnet tests.

Poster TUPDP087 [6.660 MB]

DOI •

reference for this paper ※ doi:10.18429/JACoW-ICALEPCS2023-TUPDP087

About •

Received ※ 02 October 2023 — Revised ※ 09 October 2023 — Accepted ※ 12 October 2023 — Issued ※ 13 October 2023

Cite •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TUPDP088

Labview-Based Template for Enhanced Accelerator Systems Control: Software Solutions for the CERN-ISOLDE Facilities

735

C. Charrondière, O.Ø. Andreassen, A. Benoit, E.G. Galetti, R. Heinke, L.L. Le, B.A. Marsh, R.E. Rossel, S. Rothe, S. Sudak
CERN, Meyrin, Switzerland
G.E. Boorman
Royal Holloway, University of London, Surrey, United Kingdom

ISOLDE is part of the experimental infrastructure with-in the CERN accelerator complex that provides radioac-tive ion beams for studies of fundamental nuclear phys-ics, astrophysics, condensed matter physics and medical applications. Complementing the available controls in-frastructure, an easy-to-use set of applications was devel-oped to allow operators to record and display signals from multiple sources, as well as to provide drivers for non-standard, custom-made instruments and specialized off-the-shelf components. Aimed not only at software engineers but developers with any background, a generic and modular software template was developed in LabVIEW following a collab-oration between CERN and ANGARA Technology. This unified template can be extended to support interaction with any instrument and any newly developed applica-tion can be easily added to the existing control system and integrated into the CERN control and monitoring infrastructure. New modules and instrument drivers are easy to maintain as the structure and communication layers are all derived from the same template and based on the same components. In this paper, we will explain the implementation, ar-chitecture and structure of the template, as well as a wide variety of use cases - from motor control to image acquisi-tion and laser-specific equipment control. We will also show use cases of applications developed and deployed within a few days in the ISOLDE facility.

Poster TUPDP088 [0.860 MB]

DOI •

reference for this paper ※ doi:10.18429/JACoW-ICALEPCS2023-TUPDP088

About •

Received ※ 20 September 2023 — Revised ※ 09 October 2023 — Accepted ※ 12 October 2023 — Issued ※ 23 October 2023

Cite •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

TH2BCO04

SAMbuCa: Sensors Acquisition and Motion Control Framework at CERN

1179

A. Masi, O.Ø. Andreassen, M. Arruat, M. Di Castro, R. Ferraro, I. Kozsar, E.W. Matheson, J.P. Palluel, P. Peronnard, J. Serrano, J. Tagg, F. Vaga, E. Van der Bij
CERN, Meyrin, Switzerland
S. Danzeca, M. Donzé, S.F. Fargier, M. Gulin, E. Soria
European Organization for Nuclear Research (CERN), Geneva, Switzerland

Motion control systems at CERN often have challenging requirements, such as high precision in extremely radioactive environments with millisecond synchronization. These demanding specifications are particularly relevant for Beam Intercepting Devices (BIDs) such as the collimators of the Large Hadron Collider (LHC). Control electronics must be installed in safe areas, hundreds of meters away from the sensors and actuators while conventional industrial systems only work with cable lengths up to a few tens of meters. To address this, several years of R&D have been committed to developing a high precision motion control system. This has resulted in specialized radiation-hard actuators, new sensors, novel algorithms and actuator control solutions capable of operating in this challenging environment. The current LHC Collimator installation is based on off-the-shelf components from National Instruments. During the Long Shutdown 3 (LS3 2026-2028), the existing systems will be replaced by a new high-performance Sensors Acquisition and Motion Control system (SAMbuCa). SAMbuCa represents a complete, in-house developed, flexible and modular solution, able to cope with the demanding requirements of motion control at CERN, and incorporating the R&D achievements and operational experience of the last 15 years controlling more than 1200 axes at CERN. In this paper, the hardware and software architectures, their building blocks and design are described in detail.

Slides TH2BCO04 [5.775 MB]

DOI •

reference for this paper ※ doi:10.18429/JACoW-ICALEPCS2023-TH2BCO04

About •

Received ※ 05 October 2023 — Revised ※ 12 October 2023 — Accepted ※ 19 December 2023 — Issued ※ 20 December 2023

Cite •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THPDP002

The Micro-Services of Cern’s Critical Current Test Benches

1295

C. Charrondière, A. Ballarino, C. Barth, J.F. Fleiter, P. Koziol, H. Reymond
CERN, Meyrin, Switzerland
O.Ø. Andreassen, T. Boutboul, S.C. Hopkins
European Organization for Nuclear Research (CERN), Geneva, Switzerland

In order to characterize the critical-current density of low temperature superconductors such as niobium¿titanium (NbTi) and niobium¿tin (Nb₃Sn) or high temperature superconductors such as magnesium-diboride MgB₂ or Rare-earth Barium Copper Oxide REBCO tapes, a wide range of custom instruments and interfaces are used. The critical current of a superconductor depends on temperature, magnetic field, current and strain, requiring high precision measurements in the nano Volt range, well-synchronized instrumentation, and the possibility to quickly adapt and replace instrumentation if needed. The micro-service based application presented in this paper allows operators to measure a variety of analog signals, such as the temperature of the cryostats and sample under test, magnetic field, current passing through the sample, voltage across the sample, pressure, helium level etc. During the run, the software protects the sample from quenching, controlling the current passed through it using high-speed field programmable gate array (FPGA) systems on Linux Real-Time (RT) based PCI eXtensions controllers (PXIe). The application records, analyzes and reports to the external Oracle database all parameters related to the test. In this paper, we describe the development of the micro-service based control system, how the interlocks and protection functionalities work, and how we had to develop a multi-windowed scalable acquisition application that could be adapted to the many changes occurring in the test facility.

Poster THPDP002 [6.988 MB]

DOI •

reference for this paper ※ doi:10.18429/JACoW-ICALEPCS2023-THPDP002

About •

Received ※ 06 October 2023 — Revised ※ 10 October 2023 — Accepted ※ 13 October 2023 — Issued ※ 26 October 2023

Cite •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)